ProSound

Professional Audio News & Reviews

Menu

HEDD Audio Type 07 MK2 — two-way 7-inch active studio monitors with Lineariser and CoP technologies

Maxim Liadov

We have followed Germany's HEDD Audio closely for a long time. The company started with fairly simple, affordable two-way Type 05/07 monitors, then added the multiway Type 20/Type 30. Tower Mains main monitors followed, along with the world's first full-range AMT headphones, HEDDphones ONE. Following its success and recognition among professionals, HEDD invested heavily in new technology. The first result was the Lineariser VST plug-in. It corrects speaker phase response rather than mainly frequency response. Studio monitor frequency response has rarely been a major concern, but the way sound fits together, especially in the bass, often attracts criticism.

The next step was to put a hardware DSP inside the updated MK2 monitors. Lineariser now works with any music application and any source. Phase correction inevitably adds latency, so the function can be disabled when timing is critical. The MK2 range fully replaces the previous models: only MK2 versions are now produced. New HEDD active subwoofers are available to match them.

Founder and chief designer Klaus Heinz explains the MK2 changes in official videos. We translated several videos into Russian to make the information easier to access. Unlike other monitor correction systems, Lineariser specifically addresses phase problems. These affect all speakers, whatever their design or enclosure type. HEDD monitors offer the unusual option of enabling Lineariser phase correction. You can also turn it off to hear the difference.

There is more. In a personal conversation, Klaus Heinz told us that HEDD liked the sealed enclosure design of Tower Mains so much that it brought the option to the other MK2 models. CoP, or Closed or Ported, lets the user choose. The monitors can work with open bass-reflex ports or as sealed enclosures with the ports plugged. Both approaches have advantages and drawbacks, so the choice belongs to the user.

The monitors are also ready for systems with HEDD subwoofers. Such a system retains linear phase response and time alignment between the subwoofer and monitors. A dedicated switch compensates for a satellite position up to +/-2 metres relative to the subwoofer, so sound reaches the listener at the right time.

HEDD Type 07 MK2 specifications

Drivers
Woofer 1
Basket mounting diameter 7 inches (182 mm)
Voice coil diameter 1.5 inches (38 mm)
Tweeter 1
Type HEDD AMT
Equivalent diameter 2 inches (56 mm)
Inputs
Balanced analogue XLR
AES3/EBU digital input XLR
General specifications
Amplifier (ICEpower) 2 × 100 W
Input level adjustment -10 / -4 / 0 / +4 dB
Treble EQ ±4 dB
Bass EQ ±4 dB
Frequency range 38 Hz–50 kHz
Extended frequency range 30 Hz–50 kHz
A/D and D/A conversion 32-bit, 96 kHz
Maximum peak SPL, pair at 1 m 116 dB
Crossover frequency 2.3 kHz
Balanced input impedance 22 kohms
Cabinet color Black or white
Weight 9.9 kg
Dimensions (W×H×D) 220 × 370 × 300 mm
Warranty 2 years

The main specifications have not changed: the enclosure, drivers and amplifiers remain the same. The finish is different. The previous special paint contained rubber powder. It felt pleasant but was impractical. The new MDF cabinets use a conventional durable paint, in black or white. White costs 50 euros more but looks more attractive to us.

The tweeter is still an AMT driver, a signature design found in all Klaus Heinz products. We have described it many times. Recent generations use a waveguide, allowing a lower operating frequency.

The woofer is another HEDD design. Its Ultra Honeycomb Composite cone material has a very high Young's modulus. This allows the fairly large driver to maintain piston motion up to high frequencies. The crossover frequency is 2.3 kHz.

A dedicated knob enables Lineariser, the monitors' main feature. The sound changes significantly when phase correction is on. Timbre barely changes, but bass boom disappears and the sound becomes as coherent and spacious as a full-range driver. The effect is strong. Engineers who had been unimpressed by the previous HEDD generation immediately loved the new models. The biggest change is in the bass, although the midrange also becomes more coherent and interesting. Bass parts are easier to follow and equalization is easier to judge. There are many benefits and just one drawback: 10–20 ms of latency. This cannot be avoided because low-frequency phase correction needs time. Disable Lineariser for real-time monitoring and live instrument playing through the speakers. They then behave like conventional monitors. We do not see this as a major problem. Vocals and instruments mainly occupy the midrange, where Lineariser makes the smallest correction and therefore the smallest audible difference.

The illustration shows two connection options: analogue XLR and digital AES, with a through output to the second monitor. The ANALOG/AES switch selects the input and, for AES, the right, left or mono channel. The first generation had an RCA input for unbalanced consumer sources. MK2 still accepts an unbalanced source, but you will need a suitable cable ending in a male XLR.

For analogue input, INP SENSE (dB) adjusts sensitivity to make full use of the ADC's dynamic range. A separate VOL (dB) knob controls digital volume over a wide range.

The measurement section shows the filters in action. DESK FILTER is particularly useful. It reduces boom from 100 to 300 Hz caused by surface reflections. This is unnecessary for free-standing monitors on stands, but valuable on a desk or studio mixing console.

An unusual option extends bass response to 30 Hz through DSP equalization, at the cost of amplifier headroom. We rarely find this worthwhile. At such frequencies, the cone can move beyond its linear excursion, making sound less clean even at moderate volume. It is better to let a subwoofer handle the lowest range and let the monitors reproduce the frequencies they do best. Extra bass extension always has a cost; physics cannot be avoided.

We asked Klaus whether HEDD was developing room response correction to compensate for imperfect rooms. He gave no details but pointed to the third Lineariser mode, marked with an asterisk. Further developments are possible, so we will follow HEDD's announcements.

Two bass-reflex port plugs are included to convert the monitors to sealed operation. A handle with a threaded end is used to remove them.

In theory, a sealed enclosure has an advantage in sound accuracy over a ported design. With real speakers, either can be better. A good ported design can beat a poor sealed one, and the reverse is also true. The enclosure type alone solves nothing: skilled design remains essential.

We think the HEDD Type 07 MK2 ported design works excellently with Lineariser enabled. Plugging the ports is not an automatic improvement; the result depends on the situation. We listened in a well-treated room with bass traps, where normal ported operation caused no boom. Other rooms may behave differently. One argument against sealed studio operation is that the final listener will probably use ported speakers. Consumer hi-fi and studio monitors favour that design in 99.9% of cases for its strong, extended response. Also, in sealed mode low-frequency distortion is around 10 times higher than in ported mode. In the ported design, the driver moves more freely and linearly, with less loading from the enclosed air. However, sealed operation gives tighter bass, which can be preferable in some situations. Our advice when choosing Closed or Ported is to listen with an open mind. Do not start with a theory and select only facts that support it. Practical listening is a more reliable test.

Front LEDs show operating status. The central green light indicates power; red on the left indicates overload. White on the right indicates standby, which starts after 30 minutes without a signal. Users have requested an option to disable standby completely. The manufacturer has promised it in a future firmware update. Updates use the service Ethernet port on the rear panel.

Inside is a two-channel Class D ICE Power amplifier board from Denmark's B&O, as in all HEDD monitors. It provides 100 W per channel with little heat.

The preamplifier and controls have been completely redesigned. A separate board carries the DSP, ADC and DAC. The Analog Devices SHARC DSP supplies powerful 32/40-bit processing, but HEDD engineers designed and programmed all crossovers, filters and other processing. The board is shared across the monitor range. The AK5552 ADC and AK4454 DAC have strong specifications. The analogue input ADC operates at 24-bit/96 kHz, with 115 dB dynamic range. This is the best internal design we have seen so far in this type of monitor with an ADC, DSP and DAC.

There is no fully analogue amplification mode. The analogue input always passes through the ADC and DSP because the crossovers are digital. A direct feed to the amplifiers is therefore impossible. For maximum quality, use the AES digital input. We tried both connections. We preferred digital, but analogue sounded surprisingly good and gave us no reason to complain. Other audio professionals who heard the monitors reached similar conclusions. Users have asked why HEDD chose this DAC rather than a familiar model such as the 4493. Multiway monitors need a multichannel DAC for separate digital filtering and bi-amplification. The AKM 44 series has a similar sound character across models because it uses similar digital filters and modulators. Hearing one gives a good idea of what to expect from the others.

Our main impression of the HEDD Type 07 MK2 is its sound quality. That alone would justify buying the monitors. The unique German-made drivers sound excellent, with no audible distortion, allowing hours of listening without fatigue. This matters to professionals and anyone who listens for long periods at fairly high volume. The monitors also have many other features for professionals and enthusiasts. We recommend enabling Lineariser whenever possible. CoP is a matter of taste: both sealed and ported settings sound excellent. We prefer open ports because the sound is freer and more familiar. Sealed mode is coherent but slightly restrained, and added bass EQ affects driver headroom. Remember that two-way monitors focus on the important midrange. They cannot replace three-way models or a subwoofer. The good news is that a matching subwoofer can take over the lowest range without difficult phase and frequency alignment: HEDD has already planned for this. That is another reason to consider the brand.

What are the HEDD MK2 limitations? AES is preferable to analogue. This is not an exotic interface: we had 2 Lynx Studio devices with AES outputs. Still, a suitable source is harder to find. An inexpensive Neutrik SPDIF-to-AES matching transformer is one option. We are slightly disappointed that HEDD dropped its modular input cards. For Dante, users now need to find their own Dante-to-AES converter. The same applies to other interfaces.

Frequency-response measurements

We asked the manufacturer for its official measurement graphs and will add them when they arrive. For now, here are our own measurements.

Our measurements use the hardware and software measurement system RightMark™ Audio Analyzer PRO. We also use an Earthworks M50 measurement microphone with the following specified data:

  • Serial number: 9291C
  • Sensitivity at 1 kHz: 26.4 mV/Pa
  • Frequency response variation, 20 Hz–20 kHz: 0.2 dB
  • Frequency response variation, 3 Hz–50 kHz: +1/−3 dB (roll-off from 45 kHz)

The treble adjustment graph shows a +/-4 dB range. This helps adjust the tonal balance to the amount of sound absorption in the room.

Bass adjustment also offers +/-4 dB. This is useful if one monitor is nearer a corner and produces more bass. Bass can be raised in a room with bass traps, or reduced in an untreated room.

The bass extension mode reaches below the normal ported response at the cost of maximum SPL. We did not like its sound, but you may prefer it.

The most practical filter compensates for desk or console placement and removes unpleasant upper-bass boom. The response rise near 20 kHz appears only when the microphone is exactly on the tweeter axis and at its height. Moving by just 15% flattens the response. There is no reason to worry about this extreme-treble rise. However, we measure all monitors under the same conditions, on the driver axis.

Conclusions

The HEDD Type 07 MK2 is an exceptionally interesting model and a candidate for our monitor of the year. We have long encouraged interested readers to follow HEDD Audio's work. We have supported Klaus Heinz's professional work for the past 15 years for good reason. We have bought 5 different German-designed monitor models with our own money. That is the clearest recognition of their success we can offer. While some better-known companies sell the same models for decades, HEDD continues to develop new ideas and excellent original products. Prices remain reasonable, especially for the smaller models, despite hand assembly in Germany and high-quality materials and components. Monitors are usually bought only once every 10–15 years, so choosing an ordinary cheap mass-market model makes little sense. Of course, you must like the sound of the model you choose. The whole HEDD range deserves a personal audition, for example in the demo studio at the Dr.HEAD shop on Novy Arbat in Moscow.



Note. This is an adapted machine translation into English. It follows the “In simple terms” approach. Read the original article at https://prosound.ixbt.com/monitors/hedd-07mk2.shtml.