Axelvox PM-6A — the 6-inch model in the updated budget monitor series
Grigory Liadov
We continue examining the updated Axelvox range. After the five-inch PM-5A we turn to the larger PM-6A. The new generation has redesigned ports, amplifiers, and drivers, while its appearance is almost unchanged. New models can be recognized by the power LED built into the tweeter housing rather than positioned between the drivers.
The PM series is budget studio audio intended for small project studios. There is no built-in EQ, but amplification is fully analog Class AB. A linear transformer power supply provides clean voltage without interference.
Axelvox PM-6A specifications
| Drivers | |
| Woofer | 6,5" |
| Cone | Polymer |
| Tweeter | Dome tweeter |
| Driver size | 1" |
| Amplifier | |
| Amplifier type | Analog, Class AB |
| Woofer | 80 W |
| Tweeter | 40 W |
| Crossover frequency | 2.6 kHz |
| Connections | |
| Balanced | XLR |
| Unbalanced | TRS |
| Other specifications | |
| Frequency range | 70 Hz–22 kHz |
| Maximum SPL | 89 dB |
| Signal-to-noise ratio | >100 dB |
| Cabinet | MDF, vinyl laminate finish |
| Dimensions, W × H × D | 210 × 255 × 320 mm |
| Weight | 8 kg |
The laminated MDF cabinets retain the previous classic appearance.
PM monitors use conventional fabric dome tweeters. An LED built into the tweeter housing lights bright blue when powered.
The woofers use white polymer cones. Actual cone diameter, including the surround, is 14.5 cm.
Inputs are XLR or TRS. The only adjustment is input sensitivity, with a stepped knob and level scale for convenient matching.
The bi-amplified circuit uses two TDA2050 chips. Rated peak power is 80 W for the woofer and 40 W for the tweeter. Real continuous values are lower, but output is ample for these speakers. A 60 VA dual-winding transformer provides a bipolar 18.5 V supply. A large heatsink transfers some amplifier heat to the metal rear panel.
Measurements
Our measurements use the hardware and software measurement system RightMark™ Audio Analyzer PRO. We also use the measurement microphone Earthworks M50, with the following specified data:
- Microphone serial number: 92901C
- Microphone sensitivity at 1 kHz: 26.4 mV/Pa
- Microphone frequency-response variation from 20 Hz to 20 kHz: 0.2 dB
- Microphone frequency-response variation from 3 Hz to 50 kHz: +1/−3 dB (roll-off from 45 kHz)

Frequency response measured on the tweeter axis
Measurements closely resemble the five-inch PM-5A. Coverage is 50 Hz–25 kHz within ±6 dB, while the important 100 Hz–20 kHz region stays within ±3 dB. Bass behavior is similar too: useful output starts at 50 Hz and gradually increases up to 100 Hz. Overall, the results are good.
Sound
Sound quality is high and resembles the smaller PM-5A. The Axelvox character is even, balanced, and low in distortion, supporting tonal and dynamic work as well as simple tasks.
Compared with the PM-5A, the PM-6A offers more detailed lower midrange, slightly fuller bass, and a little more volume headroom. These differences are modest; overall character and tone are the same.
The PM-6A performs very well for entry-level studio audio. One point is a small cabinet resonance around 100 Hz. We do not consider it a major problem, since much more expensive, well-known monitors have similar characteristics. If it becomes inconvenient, reduce that region by a couple of decibels on the DAW master bus or simply keep the characteristic in mind during tonal work.
The absence of built-in EQ is not a problem because little correction is needed. Sound is already reasonably even and neutral.
Conclusions
The Axelvox PM-6A repeats the PM-5A's success as a good entry-level studio monitor. We strongly recommend these models as first monitors or as an upgrade from computer speakers to more complete, higher-quality audio. They also suit a budget or small home studio.
Note. This is an adapted machine translation into English. It follows the “In simple terms” approach. Read the original article at https://prosound.ixbt.com/monitors/axelvox-pm6a.shtml.




