Koobic HAN SOLO 2i2 – affordable two-channel audio interface
We continue exploring Koobic products. After the OxyGen 25 MIDI keyboard we turn to the HAN SOLO 2i2 interface. Asian manufacturer Cuvave created Koobic specifically for Russia. Its range includes audio interfaces, MIDI keyboards, effects processors and portable guitar combos. The products target mainstream buyers and, according to the manufacturer, combine reliability, convenience and modern features. The audio interfaces are exclusive designs for the Russian market.
The Koobic HAN SOLO 2i2 is a two-channel USB interface with separate microphone and guitar inputs, a headphone output and one stereo monitor output.
The strong case uses an aluminium profile. Although interfaces often share similar designs, the HAN SOLO 2i2 stands out through its colours and glossy front, which reflects the room attractively. Controls use a familiar layout but are fairly large and convenient. There is no dedicated driver, so operation is entirely from the hardware panel.
The microphone input uses a combo XLR/TRS socket. Microphones connect through XLR only. A 48V button enables phantom power for professional condenser microphones and lights a bright red indicator. TRS sockets accept guitars or line sources. Nearby buttons switch between line and instrument modes.
An indicator lights green when input reaches -30 dB and red at overload, helping set levels safely. The 55 dB gain range is enough for comfortable dynamic microphone use. With a Shure SM58 Beta, the knob stayed below 80% of maximum.
Direct Monitor mixes input into playback without latency. There is no monitoring balance knob, so adjust playback in the DAW. Monitoring reaches both headphones and main outputs. With both inputs used, monitoring is stereo; when recording one input, its mono signal is duplicated to left and right for comfortable listening.
Separate line and headphone volume controls are convenient. They avoid constant readjustment and allow recording without switching the monitors off. Balanced TRS line output uses the largest knob. USB Type-C connects to the computer and supplies power, so no extra adapter is needed.
Koobic HAN SOLO 2i2 specifications
| Converters | |
| ADC | 107 dBA |
| DAC | 112 dBA |
| Supported formats | 44.1–192 kHz |
| Equivalent input noise (EIN) | -120 dB |
| Dynamic range | 103 dB |
| Maximum input level | 4 dBu |
| Microphone input | |
| Frequency response | 20 Hz–20 kHz |
| Gain range | 10–55 dB |
| THD+N | -98 dB |
| Equivalent input noise (EIN) | -120 dB |
| Dynamic range | 103 dB |
| Maximum input level | 4 dBu |
| Balanced line input | |
| Frequency response | 20 Hz–20 kHz |
| Gain range | -10–35 dB |
| THD+N | -94 dB |
| Equivalent input noise (EIN) | -100 dB |
| Dynamic range | 100 dBA |
| Maximum input level | 16 dBu |
| Guitar input | |
| Frequency response | 20 Hz–20 kHz |
| Gain range | -10–35 dB |
| THD+N | -94 dB |
| Equivalent input noise (EIN) | -94 dB |
| Dynamic range | 100 dB |
| Maximum input level | 16 dBu |
| Balanced line output | |
| THD+N | -94 dB |
| Equivalent input noise (EIN) | -100 dB |
| Dynamic range | 104 dB |
| Maximum output level | 20 dBu |
| Headphone output | |
| THD+N | -94 dB |
| Dynamic range | 104 dB |
| Maximum output level | 20 dBu, unloaded |
The electronics look modern, using original components with good specifications.
The digital section uses an NXP MIMXRT1011 ARM processor running at 500 MHz.
Conversion uses a multichannel AD1939 codec. Its DAC is rated at 112 dB dynamic range and -94 dB THD+N; the ADC at 107 dB and -94 dB respectively.
The analogue section uses good SMD components. A classic JRC4580 operational amplifier serves the microphone input.
A JRC4580 also drives headphones. Published output-voltage figures are slightly optimistic. We measured 1.3 V RMS, or 4.5 dBu, typical for affordable interfaces. Mainstream headphones have enough level, but high-impedance models leave little headroom. Line output was closer to specification: 3.6 V RMS, or 13.3 dBu. These are normal, practical line-output levels.
Windows 10/11 uses Microsoft's UAC 2.0 driver for stereo recording and playback up to 24-bit/192 kHz. Mac OS X also recognizes the interface for ordinary audio apps. Koobic recommends the free ASIO4ALL universal driver for HAN SOLO 2i2 use in ASIO software.
ASIO diagnostics
Features:
Input channels: 2
Output channels: 2
Input latency: 512
Output latency: 512
Min buffer size: 64
Max buffer size: 2048
Preferred buffer size: 512
Granularity: 32
ASIOOutputReady - not supported
Sample rate:
8000 Hz - supported
11025 Hz - supported
16000 Hz - supported
22050 Hz - supported
32000 Hz - supported
44100 Hz - supported
48000 Hz - supported
88200 Hz - supported
96000 Hz - supported
176400 Hz - supported
192000 Hz - supported
352800 Hz - not supported
384000 Hz - not supported
Input channels:
channel: 0 (Audio Interface 1) - Int32LSB
channel: 1 (Audio Interface 2) - Int32LSB
Output channels:
channel: 0 (Audio Interface 1) - Int32LSB
channel: 1 (Audio Interface 1) - Int32LSB
RMAA PRO measurements
For interfaces such as HAN SOLO 2i2, we measure line outputs only. Inputs always pass through preamps, so there are no direct line inputs to assess separately.
| Device under test | Audio Interface |
| Operating mode | 24-bit, 44 kHz |
| Audio interface | |
| Signal path | Line output |
| RMAA version | 6.4.5 PRO |
| 20 Hz–20 kHz filter | YES |
| Signal normalization | YES |
| Level change | -2.0 dB / -2.0 dB |
| MONO mode | NO |
| Calibration signal frequency, Hz | 1000 |
| Polarity | Correct/correct |
| Frequency response variation (40 Hz–15 kHz), dB | +0.01, -0.04 |
Excellent |
| Noise level, dB(A) | -106.6 |
Excellent |
| Dynamic range, dB(A) | 106.6 |
Excellent |
| Harmonic distortion, % | 0.00351 |
Very good |
| Harmonic distortion + noise, dB(A) | -83.8 |
Good |
| Intermodulation distortion + noise, % | 0.00688 |
Excellent |
| Stereo crosstalk, dB | -104.6 |
Excellent |
| Intermodulation at 10 kHz, % | 0.020 |
Good |
| Overall rating | Excellent |
Detailed 24-bit/44 kHz measurements are on a separate page. Results are good: low distortion and 106 dB dynamic range. These are respectable figures for an affordable device.
We also tested the HAN SOLO 2i2 in practical work with a Neumann TLM 102 condenser and Cubase in ASIO mode.
Setup and use presented no difficulties. With a suitable buffer and correct ports selected, recording and virtual instruments worked successfully. Recording quality depends more on the microphone than the interface's preamps or converters. Sound quality is good enough for professional work. A monitoring balance knob is missing, as on most similar inexpensive devices. We would also like more headphone headroom, although this is not critical. Otherwise, the HAN SOLO 2i2 is a good, competitive product.
Conclusions
The Koobic HAN SOLO 2i2 is an affordable, capable interface for personal recording and home studios. Its preamps and converters can produce professional results. Functions and controls match inexpensive interfaces from established brands. A dedicated ASIO driver and control panel are the main missing features.
Note. This is an adapted machine translation into English. It follows the “In simple terms” approach. Read the original article at https://prosound.ixbt.com/interfaces/koobic-hansolo.shtml.







