Arturia MiniFuse 2 — a two-channel audio interface from a new series
Grigory Liadov
In autumn 2021, Arturia introduced its MiniFuse audio interface series. Compared with the existing AudioFuse products, these are simpler, more affordable devices for a wide audience.
Arturia founder Frédéric Brun describes the new products: “Arturia's mission has always been to help everyone find their own sound. We have created award-winning software instruments, modern analogue and hybrid synthesizers, and smart MIDI controllers for today's producers. An audio interface is central to this workflow: a creative system connecting hardware and software, computers and creativity. Following AudioFuse, we knew we needed more affordable interfaces to make sound creation available to everyone. MiniFuse is that solution, our idea of an affordable audio companion.”
The MiniFuse series currently has three similar models, mainly differing in input count. The MiniFuse 1 has one input, the MiniFuse 2 has two and the MiniFuse 4 has four. Smaller models are already on sale; the four-channel interface is due in 2022.
Today we examine the MiniFuse 2, with two microphone/instrument inputs and two outputs.
You may remember the unusual design of the AudioFuse . MiniFuse takes a more conventional approach with familiar control positions. Arturia traditionally offers several colours; all MiniFuse models come in white or black.
Arturia MiniFuse 2 specifications
- Line inputs 1–2 (balanced TRS):
- Impedance: 16 kohms;
- Maximum level: +22 dBu;
- Gain: 56 dB;
- Frequency response: 20 Hz–20 kHz ±0.05 dB;
- Dynamic range: 110 dBA;
- THD+N: -100 dB;
- Crosstalk: -116 dB;
- Microphone inputs 1–2 (balanced XLR):
- Impedance: 2.5 kohms;
- Maximum level: +9 dBu;
- Gain: 56 dB;
- Equivalent input noise (EIN): -129 dBA;
- Frequency response: 20 Hz–20 kHz ±0.06 dB;
- Dynamic range: 110 dBA;
- THD+N: -100 dB;
- Crosstalk: -116 dB;
- Guitar inputs 1–2 (unbalanced TS):
- Impedance: 1.1 Mohms;
- Maximum level: +11.5 dBu;
- Gain: 56 dB;
- Frequency response: 20 Hz–20 kHz ±0.06 dB;
- Dynamic range: 110 dBA;
- THD+N: -100 dB;
- Speaker Out (balanced TRS):
- Impedance: 94 ohms;
- Maximum level: +12 dBu;
- Frequency response: 20 Hz–20 kHz ±0.09 dB;
- Dynamic range: 107.5 dBA;
- THD+N: -101 dB;
- Headphone output (TRS):
- Impedance: 10 ohms;
- Maximum level: +11.4 dBu;
- Frequency response: 20 Hz–20 kHz ±0.09 dB;
- Dynamic range: 104 dBA;
- Power: 137 mW.
Front combo inputs accept microphones and guitars. Three modes are available: line, microphone and instrument. Buttons with guitar symbols switch line inputs to high impedance. The front also activates +48 V phantom power.
Gain-knob indicators light blue when input signal is present and red during overload. A six-segment peak meter shows output levels.
The largest knob controls line-output level. Headphone volume is separate, an important feature because affordable interfaces often use one shared control. Here levels are independent, though the signal is the same. Direct monitoring is available, with its button and input/playback balance knob beside each other.
All knobs have rubber covers and turn with enough resistance for precise adjustment. However, as analogue controls, exact settings can be difficult. This matters little for listening volume, but setting gain to a precise decibel value takes practice.
The rear has balanced TRS outputs, full-size five-pin MIDI input and output, a hub with an extra USB port, and the USB Type-C computer connection. The interface uses USB bus power only, and a cable is included.
The interface uses an XMOS XU-208 processor.
Conversion uses the common CIRRUS LOGIC CS4272 stereo codec. Specifications are good: 114 dB dynamic range and THD+N <-100 dB (<0.001%).
The op-amps are JRC4580 types.
Most inexpensive interfaces have low-power headphone amplifiers. Arturia paid special attention to this circuit in the MiniFuse 2, producing an interesting, powerful output. Specified power is an impressive 137 mW.
High headphone power may be unnecessary for ordinary music playback. During microphone recording and monitoring, however, more volume is often needed. A comfortable microphone/backing-track balance can put the mix control near the input end, while the microphone is recorded with headroom below clipping. Headphone level can then be insufficient. The MiniFuse 2 avoids this with an output loud enough for common headphones.
The panel mainly shows input levels more precisely. Almost all control takes place on the hardware. Advanced settings select sample rate and ASIO buffer size.

A standard ASIO buffer panel is also available. Safe Mode helps prevent clicks on laptops with less powerful CPUs.

Latency is very low: 5 ms with a 64-sample buffer. Output-only latency is lower still.
Device: MiniFuse ASIO Driver
Features:
Input channels: 4
Output channels: 4
Input latency: 710
Output latency: 551
Min buffer size: 8
Max buffer size: 2048
Preferred buffer size: 512
Granularity: -1
ASIOOutputReady - not supported
Sample rate:
8000 Hz - not supported
11025 Hz - not supported
16000 Hz - not supported
22050 Hz - not supported
32000 Hz - not supported
44100 Hz - supported
48000 Hz - supported
88200 Hz - supported
96000 Hz - supported
176400 Hz - supported
192000 Hz - supported
352800 Hz - not supported
384000 Hz - not supported
Input channels:
channel: 0 (MIC/LINE/INST 1) - Int32LSB
channel: 1 (MIC/LINE/INST 2) - Int32LSB
channel: 2 (LOOPBACK Left) - Int32LSB
channel: 3 (LOOPBACK Right) - Int32LSB
Output channels:
channel: 0 (Output Left) - Int32LSB
channel: 1 (Output Right) - Int32LSB
channel: 2 (LOOPBACK Left) - Int32LSB
channel: 3 (LOOPBACK Right) - Int32LSB
Diagnostics show modes up to 192 kHz, with four inputs and four outputs. Two correspond to physical I/O. Two extra LOOPBACK channels provide virtual sources for recording, broadcasting and streaming apps, a very useful function.
RMAA testing
| Device under test | [ASIO] MiniFuse ASIO Driver |
| Operating mode | 24-bit, 44 kHz |
| Audio interface | ASIO |
| Signal path | External loopback (line-out - line-in) |
| RMAA version | 6.4.5 PRO |
| 20 Hz–20 kHz filter | ON |
| Signal normalization | ON |
| Level change | -0.2 dB / -0.1 dB |
| MONO mode | OFF |
| Calibration signal frequency, Hz | 1000 |
| Polarity | inverted/inverted |
| Frequency response variation (40 Hz–15 kHz), dB | +0.11, +0.00 |
Excellent |
| Noise level, dB(A) | -107.5 |
Excellent |
| Dynamic range, dB(A) | 107.5 |
Excellent |
| Harmonic distortion, % | 0.00084 |
Excellent |
| Harmonic distortion + noise, dB(A) | -93.9 |
Very good |
| Intermodulation distortion + noise, % | 0.00187 |
Excellent |
| Stereo crosstalk, dB | -95.3 |
Excellent |
| Intermodulation at 10 kHz, % | 0.00166 |
Excellent |
| Overall rating | Excellent |
See the RMAA report for details
Measurements are very good and confirm the stereo codec specifications. The spectrum is clean and tests found no problems. These are good results for an affordable interface.
We tested the microphone preamps with a Neumann TLM102 condenser. For an affordable interface, recording quality is good, bright and detailed. The MiniFuse 2 caused no operational problems. Gain controls could be more precise, and inputs cannot be muted in the control panel. Otherwise, it performed very well. The powerful headphone output made every stage comfortable, and separate volume control avoids disconnecting monitors while recording.
Included software includes Ableton Live Lite, Analog Lab Intro virtual instruments, Arturia FX effects, Native Instruments GUITAR RIG 6 LE, and three-month access to Splice Creator Plan and Auto-Tune.
Conclusions
The Arturia MiniFuse range is interesting. MiniFuse 2 feels carefully designed despite its basic feature set. Arturia has created an affordable, competitive USB recording interface. Strengths include a cast-metal case, powerful headphone output, separate volume controls, extra Loopback channels, a USB hub and a generous software bundle.
Note. This is an adapted machine translation into English. It follows the “In simple terms” approach. Read the original article at https://prosound.ixbt.com/interfaces/arturia-minifuse2.shtml.








