Arturia MiniFuse 1 – the most affordable MiniFuse interface
Grigory Liadov
The MiniFuse 1 is the most affordable audio interface from French manufacturer Arturia. Unlike larger models, the MiniFuse 1 has only one microphone/instrument input and no MIDI connection. Other main MiniFuse features remain, including 114 dB converters, Loopback channels, a USB hub and a powerful headphone output with separate volume control.
The MiniFuse series appeared in 2021 and currently includes three similar models, mainly differing in input count. We previously reviewed the two-channel MiniFuse 2; now we examine the smallest model, MiniFuse 1.

Audio interfaces usually come in one colour. Arturia offers MiniFuse cases in traditional black or bright white.
Arturia MiniFuse 1 specifications
- Line input (balanced TRS):
- Impedance: 16 kohms;
- Maximum level: +22 dBu;
- Gain: 56 dB;
- Frequency response: 20 Hz–20 kHz ±0.05 dB;
- Dynamic range: 110 dBA;
- THD+N: -100 dB;
- Crosstalk: -116 dB;
- Microphone input (balanced XLR):
- Impedance: 2.5 kohms;
- Maximum level: +9 dBu;
- Gain: 56 dB;
- Equivalent input noise (EIN): -129 dBA;
- Frequency response: 20 Hz–20 kHz ±0.06 dB;
- Dynamic range: 110 dBA;
- THD+N: -100 dB;
- Crosstalk: -116 dB;
- Guitar input 1 (unbalanced TS):
- Impedance: 1.1 Mohms;
- Maximum level: +11.5 dBu;
- Gain: 56 dB;
- Frequency response: 20 Hz–20 kHz ±0.06 dB;
- Dynamic range: 110 dBA;
- THD+N: -91 dB;
- Speaker Out (balanced TRS):
- Impedance: 94 ohms;
- Maximum level: +12 dBu;
- Frequency response: 20 Hz–20 kHz ±0.09 dB;
- Dynamic range: 107.5 dBA;
- THD+N: -101 dB;
- Headphone output (TRS):
- Impedance: 10 ohms;
- Maximum level: +11.4 dBu;
- Frequency response: 20 Hz–20 kHz ±0.09 dB;
- Dynamic range: 104 dBA;
- Power: 137 mW.
The strong metal case has rubber feet to prevent sliding while adjusting controls.
The combo input accepts a microphone or guitar. Line mode is also available, though less likely to be needed with a single input. A button with a guitar symbol switches input mode. Front controls also activate +48 V phantom power.
Gain and headphone knobs have illuminated indicators that help show their settings. Input signal lights blue, changing to red during overload. The largest knob controls line-output level, shown by a six-segment peak meter.
MiniFuse headphone volume is independent. Inexpensive interfaces often share one control for headphones and line output. Here, although the signal is identical, levels are separate. Direct monitoring is available, but the smallest model lacks input/playback balance adjustment.
Balanced TRS line outputs are on the rear, alongside a hub with one extra USB port and the USB Type-C computer connection. USB bus power is the only power source. A cable is included. Arturia specifies Windows 7 or later and Mac OS X 10.10 or later.
MiniFuse 1 electronics largely match the larger models.
The interface is based on an XMOS XU208 microcontroller.
Conversion uses the common CIRRUS LOGIC CS4272 stereo codec. Specifications are good: 114 dB dynamic range and THD+N <-100 dB (<0.001%).
JRC4580 op-amps are visible on the board.
The MiniFuse 1 headphone output is as powerful as those on other models in the series. High power may be unnecessary for ordinary music listening, but recording monitoring needs enough level for performer comfort. Setting input/backing-track balance is usually easy; achieving sufficient volume at that balance is not always possible. MiniFuse devices avoid this problem. Specified power is an impressive 137 mW, uncommon even in much more expensive interfaces.
Almost all controls are on the hardware. The MiniFuse panel shows input levels more precisely and selects sample rate and ASIO buffer size.

A standard ASIO buffer panel is also available. Safe Mode is intended for use with less powerful laptops.

Latency is low: just 6 ms with a 64-sample buffer. Output-only latency is lower still.
Device: MiniFuse ASIO Driver
Features:
Input channels: 4
Output channels: 4
Input latency: 710
Output latency: 551
Min buffer size: 8
Max buffer size: 2048
Preferred buffer size: 512
Granularity: -1
ASIOOutputReady - not supported
Sample rate:
8000 Hz - not supported
11025 Hz - not supported
16000 Hz - not supported
22050 Hz - not supported
32000 Hz - not supported
44100 Hz - supported
48000 Hz - supported
88200 Hz - supported
96000 Hz - supported
176400 Hz - supported
192000 Hz - supported
352800 Hz - not supported
384000 Hz - not supported
Input channels:
channel: 0 (MIC/LINE/INST 1) - Int32LSB
channel: 1 (MIC/LINE/INST 2) - Int32LSB
channel: 2 (LOOPBACK Left) - Int32LSB
channel: 3 (LOOPBACK Right) - Int32LSB
Output channels:
channel: 0 (Output Left) - Int32LSB
channel: 1 (Output Right) - Int32LSB
channel: 2 (LOOPBACK Left) - Int32LSB
channel: 3 (LOOPBACK Right) - Int32LSB
ASIO diagnostics show modes up to 192 kHz, with four inputs and four outputs. Two inputs and outputs correspond to physical I/O, while two extra LOOPBACK channels provide virtual sources for recording, broadcasting and streaming applications. The second input in this single-input interface appears only in ASIO apps and duplicates the first input's signal.
RMAA testing
| Device under test | [ASIO] MiniFuse ASIO Driver |
| Operating mode | 24-bit, 44 kHz |
| Audio interface | ASIO |
| Signal path | External loopback (line-out - line-in) |
| RMAA version | 6.4.5 PRO |
| 20 Hz–20 kHz filter | ON |
| Signal normalization | ON |
| Level change | -1.8 dB / -1.8 dB |
| MONO mode | OFF |
| Calibration signal frequency, Hz | 1000 |
| Polarity | inverted/inverted |
| Frequency response variation (40 Hz–15 kHz), dB | +0.02, -0.09 |
Excellent |
| Noise level, dB(A) | -108.3 |
Excellent |
| Dynamic range, dB(A) | 108.4 |
Excellent |
| Harmonic distortion, % | 0.00119 |
Excellent |
| Harmonic distortion + noise, dB(A) | -92.4 |
Very good |
| Intermodulation distortion + noise, % | 0.00222 |
Excellent |
| Intermodulation at 10 kHz, % | 0.00177 |
Excellent |
| Overall rating | Excellent |
See the RMAA report for details
Measurements are excellent overall and confirm the stereo codec specifications. These are very good figures for an affordable device. Because MiniFuse 1 electronics match the MiniFuse 2, results are similar.

The MiniFuse 1 preamp matches larger models. Recording quality is good, bright and detailed. We encountered no operating problems. Analogue gain control and the lack of monitoring-balance adjustment took some getting used to, but everything else worked very well. The powerful headphone amplifier, separate headphone/line volume and streaming Loopback channels deserve mention again.
Conclusions
The MiniFuse 1 looks attractive and is as interesting as its larger relatives. For an entry-level interface, it offers good sound and many functions. The generous software bundle includes Ableton Live Lite, Analog Lab Intro virtual instruments, Arturia FX effects, Native Instruments GUITAR RIG 6 LE, and three-month access to Splice Creator Plan and Auto-Tune.
Note. This is an adapted machine translation into English. It follows the “In simple terms” approach. Read the original article at https://prosound.ixbt.com/interfaces/arturia-minifuse1.shtml.







